xmoonproductions.org
https://xmoonproductions.org/

Plasma Collision - and 3.0 Walkthrough
https://xmoonproductions.org/viewtopic.php?f=8&t=3438		 Page 4 of 5
Author:  skidrow [ Mon Jan 26, 2015 6:33 pm ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
Go out from your room and follow the slim and you find it :)
Author:  TheBeatles [ Thu Jan 29, 2015 9:57 am ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
Can't slide the card on 16th floor. There's some kind of invisible wall...
Author:  skidrow [ Thu Jan 29, 2015 6:35 pm ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
Wrong floor it at 17 or 19 you should go.
Author:  Malachai [ Thu Jan 29, 2015 7:12 pm ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
TheBeatles wrote:
Can't slide the card on 16th floor. There's some kind of invisible wall...


You don't use your card when you get to the required floor. You need to use your mouse cursor to click and hold down on the device next to the door. It's a thumb scanner. I was fooled by that in the beginning as well.
Author:  TheBeatles [ Sat Jan 31, 2015 2:59 am ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
Malachai wrote:
TheBeatles wrote:
Can't slide the card on 16th floor. There's some kind of invisible wall...


You don't use your card when you get to the required floor. You need to use your mouse cursor to click and hold down on the device next to the door. It's a thumb scanner. I was fooled by that in the beginning as well.

Thank you. It worked.
Author:  ottawaguy05 [ Fri Jul 01, 2016 8:43 pm ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
Hey folks,

so all steps followed, container in the left pod and closed, servers on, reactors powered valves open. set the shift on reactor 2 to 17.5, got collision and maxed the speed, eventually reads portal stable, meanwhile reactor 1 was set at 20.5 max speed read collision, no portal just the smallest flicker, and it stays that way. What am I missing???
Author:  skidrow [ Fri Jul 01, 2016 10:43 pm ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
ottawaguy05 wrote:
Hey folks,

so all steps followed, container in the left pod and closed, servers on, reactors powered valves open. set the shift on reactor 2 to 17.5, got collision and maxed the speed, eventually reads portal stable, meanwhile reactor 1 was set at 20.5 max speed read collision, no portal just the smallest flicker, and it stays that way. What am I missing???


Make sure you dont have -
Author:  ottawaguy05 [ Sat Jul 02, 2016 12:08 am ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
skidrow wrote:

Make sure you dont have -


reactor one is set to +20.5, not negative 20.5. It is producing a spark but just stays small, does not get bigger over time like the other one.
Author:  skidrow [ Sat Jul 02, 2016 8:13 am ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
ottawaguy05 wrote:
skidrow wrote:

Make sure you dont have -


reactor one is set to +20.5, not negative 20.5. It is producing a spark but just stays small, does not get bigger over time like the other one.


Then you probably dont have it at full speed.
Author:  ottawaguy05 [ Sun Jul 03, 2016 2:55 pm ]
Post subject:  Re: Plasma Collision - and 3.0 Walkthrough
Then you probably dont have it at full speed.[/quote]

1140 is max speed. maybe the container isn't perfectly centered in the chamber is whats causing issues or something (I put it in the middle of the place me here square)

I tried again from scratch and followed the order of the pop ups, screens, reactors power, then the container, reactor valves, injected plasma, set #1 to 20.5 speed to 1140, #2 17.5 speed 1140, after 10 mins of so the #2 portal stabilized, no change to #1 after 20 mins, tried going to city view advancing time an hour went back and waited another 20 minutes, for absolutely nothing.

What am I missing here folks?
Page 4 of 5 All times are UTC
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/